I often get asked about mobile ham radio installations, so I thought I would post some tips on that subject.
First and foremost, good grounding is of prime importance, especially doors and hoods. In every vehicle I have owned, I took a piece of 1/2" ground braid and put crimped ring-tongue solderless terminals on each end then fastened it between every door and the frame. I did the same to the hood and frame. Remember to do the same to the car's trunk, too. This practice ensures that each component of the vehicle has the same ground potential. Even tho the doors and hoods are connected by hinges, you have to remember that those hinges have grease on them and grease is an insulator when it comes to electrical current and ground paths.
The exhaust pipe can act like a giant antenna, too, causing QRM. It is not connected to the frame of the vehicle solidly because it needs to "float" by means of some special brackets that have a piece of thick rubber in between. So, I take a piece of ground braid and connect it between one of the muffler clamps and a bolt on the frame. If there is no bolt nearby, find a thru hole in the frame and stick a bolt thru it. Or, you could drill and tap a 1/4-20 hole in the frame and fasten the braid to that bolt. Make sure you use a lockwasher on that bolt to keep it from vibrating loose. If there is any undercoating on the frame, scrape a little of it off before inserting the bolt, then once it is tight, spray some touch-up undercoating on the bolt.
The DC power line should be ran directly from the battery thru the firewall to a screw terminal strip inside the vehicle. Make sure the terminal strip has enough terminals to acomodate all of the stuff you will be hooking to it. I use #10 stranded wire for the battery run and it is the red/black DC wire that is standard for automotive work. At the battery end, solder in an in-line fuse holder and fuse it with a 25 amp fuse. Also, at that same end, put a big snap choke there with as many turns of wire as you can get on it. Put another snap choke on the other end of the DC cable. This will help attenuate alternator whine and fuel pump noise. Snap chokes can be purchased from www.allelectronics.com fairly cheap.
Lets talk a bit about antenna installations. With dual band 2M/70cm antennas, I always try to use a mag mount and I put it right in the middle of the roof. This gives the antenna a good ground plane for the signal to reflect off of. The signal will be strongest in whatever direction the vehicle is facing, front or back. If you have a regular car, you can use a trunk lip mount for the antenna and that will work OK, too. Routing the coax from a roof mounted antenna, I just run the coax to a rear door and shut the door on the coax somewhere near the top. I don't usually have any problems with water leaking in when it rains. Routing the coax from a trunk lip mount can be tricky because you have to snake it under the back seat and up front to the radio.
What is the next thing you need to do now that you have the radio and antenna installed? Check the SWR! For this you will need a good quality SWR/Power meter. You will need to set the radio on a simplex frequency such as 146.520 and check the SWR there. A reading of 1.3 or lower is acceptable. Now set the radio to the 70cm band and put the frequency at 449.00. Why 449? Because most 440 repeaters have a 5 khz split between the receive and transmit frequencies. In other words, if you are on a repeater that is on 444.100, your rig will transmit on 449.100. This is where you need to check your SWR. Most dual band antennas don't have SWR readings that are equal on both bands. Sometimes you have to play with the adjustable whip on the antenna to strike a happy medium. I try to get them as close as possible to each other. There have been times when I have had to trim a bit of material off the bottom of the whip with a bench grinder, but you have to be VERY CAREFUL about this. If you trim even a few thousandths of an inch too much, it can change the SWR dramatically. Don't do this unless there is no alternative. Another option is to raise or lower the position of the whip in its socket then tighten down the setscrew.
Now lets talk a little bit about HF antennas. I have used Ham Stick antennas and Hustler antennas but the drawback of those is that in order to change bands, you have to change antennas, which can be a big pain in the butt. I thank God for the invention of the screwdriver antenna! The one I use on my truck is the Little Tarheel II which will transmit on 80 thru 6 meters. Again, the key to getting an antenna to work well is a GOOD GROUND. On my truck, I took a piece of 1/8" aluminum and bolted it between the tool box and the truck bed with about half the material sticking out beyond the truck bed. The antenna is mounted thru a hole in the material. I then ran a piece of copper wire from that plate to the frame of the truck for the ground connection. This arrangement works well. It is out of the way and yet high enough for the antenna to use the roof as a ground plane. I use an Ameritron screwdriver antenna controller for tuning but it can be a pain in the butt because if the antenna loses its position, the preset position numbers on the controller will be off, too. That is why I have ordered an autotuner for the antenna. I have not installed it yet and I do not remember the name of it, but as soon as I get it installed and working, I will add a product review to this blog.
The radio I use in the truck is the Yaesu FT-857D because it has HF, VHF and UHF all in one box. Believe me, I use all of its capabilities, too. I have had it since 2007 and it has been a very good performer. When I am on HF, a lot of guys can't believe I am mobile because they don't hear any noise from the truck! I guess the noise cancelling ability of the stock mic works quite well. There are times when I wish I had an amplifier in the truck for HF, but then I would need a heavier duty screwdriver antenna to handle the extra power....maybe someday.
Monday, September 3, 2018
Wednesday, February 24, 2016
Frequently Asked Questions About Ham Radio
Why are you called “hams”?
Nobody knows for sure, but my own theory
is that when ham radio first began, our radios had to be built from scratch,
and the only mode of operation was AM. I
think the word HAM meant “Homemade AM.”
However, HAM can mean Help All Mankind,
because when disaster strikes, we hams are some of the first on the scene. Remember the Great Flood of 1993 along the
Mississippi River? Ham radio operators
spent countless hours relaying messages, hunting for survivors, handling
logistics, and many other things on their own time and at their own expense.
Here in Illinois and throughout the
Midwest, we most often do weather spotting.
When severe weather threatens, trained spotters are sent out into the
countryside around the cities and towns to watch for tornado activity in the
sky and report back via VHF or UHF radio to their “net control station” which
is usually located at the Emergency Operations Center at ESDA headquarters or a
firehouse. The net control operator also
watches the Doppler radar display on the Internet and warns his spotters of
imminent danger in their location.
Helping others in any way we can, is our
“prime directive”. When disasters occur,
often times the phone lines are down and electrical power is knocked out. All normal means of communication are
useless...even cell phones. Our job is
to be constantly on the cutting edge of technology and to be ready to set up
our stations at a disaster site at a moment’s notice. Field Day is our once per year opportunity to
test our equipment and expertise at communicating under difficult conditions
outside our homes. Many ham radio clubs
work closely with local governmental and disaster agencies throughout the year
in planning for disaster management.
How far can you talk?
That depends on the type of radios we use,
and what modes of operation we use. If
we were to use VHF or UHF radios, they would have a range of about 15 miles if
we did not go through a repeater system.
If we use a repeater, our range would be extended to about a 35-mile
radius of the repeater’s location. A
repeater is basically a remote radio site, which takes our transmitted signal
and rebroadcasts it simultaneously at a higher power level. Repeaters are usually located on the tops of
tall buildings, or commercial radio towers.
There are many thousands of repeaters on many different bands all across
the U.S. and the world, which are owned and operated by ham radio clubs and
individuals.
If
we were to use a radio, which operates below 30 MHz, we can talk all around the
world if propagation conditions are good.
We call these bands the High Frequency bands, or HF for short. Back in the early days of ham radio, many
thought that the highest they could possibly go in radio frequencies was 30 MHz
because the technology to do otherwise did not exist at the time. Now, however, things are different. Some ham operators have been experimenting
with frequencies in the 24 GHz
(Gigahertz) range, which is at the high end of the microwave band.
Since the Space Shuttle missions began,
ham radio has been onboard, and we have been able to talk to the astronauts
directly. Many hams have set up stations
at schools around the country and let the school children ask the astronauts
questions. The first astronaut to use
ham radio aboard a shuttle was Owen Garriott, W5LFL.
Some hams with a lot of real estate for
large antennas have been able to bounce VHF radio signals off the Moon and back
to Earth. We call this mode EME, which
stands for Earth-Moon-Earth. The signals
that come back from the moon are quite weak, so a large antenna array is needed
to pick them up. Receiver preamplifiers
are also needed to boost the incoming signals.
Most EME transmissions are done in Morse Code. A lot of transmit power is also needed for
signals to reach the moon. Many
operators use up to the legal limit of 1500 watts.
What is the difference between CB and Ham
Radio?
There is a HUGE difference. CB radios
are cheaply made and poorly designed.
They only put out 4 to 5 watts on AM and 12 watts on SSB. On a good day you might be able to talk
reliably out to 15 miles or so. CB
radios are limited to only 40 frequencies or channels, which is a very tiny chunk
of radio spectrum. In ham radio, we use
entire BANDS of frequencies. For
example, in the 14 MHz band we are allowed to use all frequencies from 14.000
to 14.350 MHz. There are no assigned
“channels”. That is only one band out of
the 10 that we have in the HF frequency spectrum. I haven’t even mentioned the VHF or UHF
bands. So, you can see how much more
versatility we have in ham radio as opposed to CB. Furthermore, we are allowed to experiment
with our equipment to enhance its performance.
That is why we are officially called Amateur Radio Operators. CBers are not allowed to do that. We can even build our own equipment if we
want to, but there are rules and practices to be followed in doing so. That is why we are required to take written
exams.
CB
is not a regulated radio service the way ham radio is. The only time the FCC steps in on CBers is in
cases where repeat offenders cause malicious interference to other radio
services or run amplifiers. Running an
amplifier of any kind on CB is strictly forbidden.
I used to be a CBer back in the early
1970s but I eventually got tired of all the operators interfering with each
other, channel bleed-over and profanity on the air. In 1979 I was introduced to some ham radio
operators in the Gibson City, IL area and they started a ham radio class. On May 20, 1979 I took my ham radio exam and
became a Novice operator. I sold all of
my CB stuff and bought my first ham radio.
You guys still use Morse
Code? I thought that was outdated long
ago!
Much
to the surprise of many, Morse Code or “CW” is still used today, but to a
lesser extent. It is still a reliable method of communication,
and the simplest to use. The fact that
Morse signals are high-pitched audio tones, gives them the ability to be heard
more readily through interference and static.
With electronic filtering devices, we are able to decrease the level of
interference and narrow the bandwidth of our radios so that we hear only the
signals we wish to receive. Other CW
signals which would be audible and within the bandwidth of the radio’s receiver
would be blocked out. You can’t do that
to as great an extent with voice signals without losing a lot of signal
quality.
Receiving Morse Code is like reading
music, only in reverse. With music, you
read the music on the paper, and translate those notes into sound. With Morse Code, you listen to the sound,
then translate that sound to words written on paper. Some operators are so good at CW (Continuous
Wave - another name for Morse Code) that they can copy it in their head at over
40 words per minute, and never have to write anything down!
How do your radio signals go
clear around the world?
Our radio signals are reflected back down
to Earth by bouncing off a layer of ionized air about 50 to 250 miles above the
Earth. It is called the ionosphere
because it is made up of electrically charged oxygen molecules, called
ions. These molecules are charged by the
sun’s “solar wind”. Within the
ionosphere, there are 3 inner layers called the E, F1, and F2 layers.
The E-layer is made up of patches of
ionized air and these float around up there.
That is why we hear signals fade in and out on some of our bands because
these patches of air move and change the angle at which our signals are
reflected back down to the Earth. The
50-54 Mhz band, called 6 meters, is affected by the E-layer. When propagation is favorable on 6 meters,
many hams get on the air and make as many quick contacts as possible before the
conditions fade.
The F1 and F2 layers combine at night to
form one layer, and this enables our signals to go farther distances. These layers do not move around, in patches
like the E-layer does. These layers of
ionosphere basically act as a mirror in reflecting radio waves. Many times our radio waves make many “hops”
across the earth in this manner, and that is how we can communicate with other
hams across the world.
When the sun is highly active, it produces
solar flares. These huge masses of
electromagnetic plasma, x-rays and gama rays produce massive amounts of “solar
wind”, and they can disrupt our communications systems. We hams are especially aware of this, and we
are watchful of the U.S. government’s measurements of this activity. These measurements of geomagnetic activity
are broadcast every hour at 18 minutes past the hour on WWV, the station where
the Atomic Clock is located. Visit their
website: www.nist.gov for more
information. Also read the July 2004
issue of National Geographic for more information on the latest findings on the
sun’s makeup via NASA’s SOHO orbiter.
Another good website to visit is www.solarham.com
.
How
many ham operators are there?
At the last count, there were around 3 million
worldwide, and the numbers are growing.
Japan actually has more hams than the U.S. does. There are
26,206 hams in Illinois and over 800,000 hams in the U.S.
What do you use computers
for in this hobby?
That would be a long list if I told you everything
we use computers for. One of the main
things we use them for is generating digital signals and transmitting them
through our radios. A lot of our
software for digital communications utilizes the computer sound card to
generate and receive digital signals.
The software decodes the signals we hear and displays the text on the
computer monitor. Then when we transmit,
the computer sound card generates the necessary signals, which are put through
the mike jack on the radio. The computer
also puts the radio into “transmit” mode.
In order to properly do this, we use an interface, which lets the
computer control transmit and receive modes.
Another interesting mode, which utilizes our computers, is called
Slow-Scan TV, but it actually has nothing to do with television. Until the personal computer came along,
however, you did need a small TV camera and interfacing equipment to transmit
still
Sunday, December 27, 2015
Improving the MFJ-2990 Vertical antenna.
I have owned the MFJ-2990 vertical antenna since May of 2009. It has been a great performer but it has some design flaws.
First of all, the sections of aluminum tubing are held in place by hose clamps. These tend to loosen with time and vibration. Once I had the thing adjusted and tunable on all the bands I work on the radio, I put a sheet metal screw in each section near the hose clamp to make sure the sections don't slide down and de-tune the antenna.
An antenna this long (43 ft.) tends to vibrate in the wind especially if it has guy ropes attached to it. I would not recommend installing it without guy ropes, especially in windy climates like Illinois has. The vibration tends to loosen clamps and other components.
The balun box is poorly designed. The box is held in place at the base of the antenna by two hose clamps which also serve as contact points to the antenna. This is not a good thing because the clamps tend to get dirt behind them and the aluminum of the antenna tends to corrode there. To fix this issue, I disconnected the wire that feeds signal to the hose clamps and terminated it to a stainless steel bolt which I installed in the side of the box. See figure 1. The cable I used for the outside connection to the antenna is plain old #12 copper wire. The cable you see in this photo is the center conductor of LMR-400 coax. It dry-rotted over time and I had to replace it. I then connected the other end of the cable to the antenna by means of a 10-32 stainless steel screw tapped into the side of the antenna.
First of all, the sections of aluminum tubing are held in place by hose clamps. These tend to loosen with time and vibration. Once I had the thing adjusted and tunable on all the bands I work on the radio, I put a sheet metal screw in each section near the hose clamp to make sure the sections don't slide down and de-tune the antenna.
An antenna this long (43 ft.) tends to vibrate in the wind especially if it has guy ropes attached to it. I would not recommend installing it without guy ropes, especially in windy climates like Illinois has. The vibration tends to loosen clamps and other components.
The balun box is poorly designed. The box is held in place at the base of the antenna by two hose clamps which also serve as contact points to the antenna. This is not a good thing because the clamps tend to get dirt behind them and the aluminum of the antenna tends to corrode there. To fix this issue, I disconnected the wire that feeds signal to the hose clamps and terminated it to a stainless steel bolt which I installed in the side of the box. See figure 1. The cable I used for the outside connection to the antenna is plain old #12 copper wire. The cable you see in this photo is the center conductor of LMR-400 coax. It dry-rotted over time and I had to replace it. I then connected the other end of the cable to the antenna by means of a 10-32 stainless steel screw tapped into the side of the antenna.
| Figure 1. |
The next thing I did was to take out the two blue capacitors and mount them to a circuit board and re-solder them into the box. One time I could not figure out why the antenna would not tune, so I looked inside the balun box and discovered that one of the wires from the capacitors had broken off! This was puzzling to me, but I figured out that it must have been vibration that caused the connection to weaken. Putting the capacitors on a circuit board then soldering in some heavier wire for the connection to the coax connector cured the problem. See figure 2.
Next, I found that the ground wire connection to the base plate of the antenna was not very good. I had mistakenly used a zinc terminal on the end of the earth ground wire to connect to the base plate. These two metals don't like each other. I took the terminal off and installed a connector made of an alloy that is friendly with copper and aluminum. I bolted it on with a stainless steel bolt and then polished up the end of the ground wire with sandpaper. Then, before inserting the end of the copper ground wire, I smeared some Gardner-Bender No-Ox on the end of the wire. Then I tightened the connector's set screw. See figure 3.
Figure 3.
Figure 3.
Make sure you don't forget to insert the black wire from the bottom of the balun box into the connector as shown.
These improvements have made a big difference in keeping the antenna in good condition and functioning normally. Remember that using stainless steel bolts and other hardware are the only way to go when constructing antennas. They don't corrode or rust and you won't have to replace them unless they break.
73. Your comments are welcome.
Thursday, June 11, 2015
Weather Stations - You Get What You Pay For...Most of the Time.
Last August my LaCrosse Technologies Weather Station model WS-2812U-IT went belly-up after just over one year of use. The anemometer quit on me. I opened up the anemometer to see if there was any kind of damage, but I only found that the batteries were dead. I found out the hard way that taking the thing apart is difficult due to one part in particular. It is a little piece of black plastic in an L shape that covers 5 little LEDs. If you break this little piece of plastic, you are SCREWED! A black plastic disk goes in between it and the LEDs to sense the wind speed. The plastic disk is on the shaft for the wind cups. I tried to fix my anemometer but failed. I contacted the company and sent the whole thing back. They returned it with a new anemometer inside for free. I set it all back up again and found that the new anemometer DID NOT WORK right out of the box! I was thoroughly disgusted, to say the least, so I decided "I am done with this company!"
I went on-line and searched for weather stations of different brands and found one that suits my needs. It cost me $200 but I found it was well worth it. It is made by Meade Instruments and it is the model TE923W-M. This puppy has the usual indoor/outdoor temp and humidity, barometer, wind speed and direction, and rainfall, plus a UV sensor for sunburn risk, moon phase, sunrise/sunset times, and wind chill. It even has a remote! You can even have it backlit in blue, but the backlight only stays on for about 30 seconds or so. The barometer has a bar graph that constantly updates showing you changes in pressure. It comes with software for making charts and graphs of weather data. It is called Weather Capture Advance V 1.2. It is pretty darn cool! I had no trouble at all setting it up. This program also saves the weather data in an archive file so you can access it as needed. I used to have a weather station made by MFJ Enterprises a few years ago and it had a nasty software program called Heavy Weather. It took me forever to figure that program out!
In summary, let me say that I am very pleased with this new weather station. I think I got a good value for my money. LaCrosse will not see another dime from me, tho.
Here is an update on the Meade weather station. When I updated my computer to Windows 7, I found that the Meade software would not work. I went on-line to the Meade website and found that they don't provide updates to their software packages! I tried looking elsewhere on-line for software that might work but I had no luck. By this time, the weather station was showing its age and battery life was getting shorter, so I decided to go shopping for yet another weather station.
I ended up with a nice one from Acurite, which cost $225. The outside unit was an all-in-one outfit and it sends data wirelesssly to a receiving unit inside the house and that unit is connected to my router, which sends the data to a website from which I can access my data from any Wi-Fi hotspot or standard internet connection. THAT is COOL! The display unit is a full-color LCD outfit with back-lighting. I usually have to change batteries in the sending unit about every 4 months. I did not put the sending unit up very high this time. It is about 12 ft. off the ground on a self-supporting mast and works fine there.
I went on-line and searched for weather stations of different brands and found one that suits my needs. It cost me $200 but I found it was well worth it. It is made by Meade Instruments and it is the model TE923W-M. This puppy has the usual indoor/outdoor temp and humidity, barometer, wind speed and direction, and rainfall, plus a UV sensor for sunburn risk, moon phase, sunrise/sunset times, and wind chill. It even has a remote! You can even have it backlit in blue, but the backlight only stays on for about 30 seconds or so. The barometer has a bar graph that constantly updates showing you changes in pressure. It comes with software for making charts and graphs of weather data. It is called Weather Capture Advance V 1.2. It is pretty darn cool! I had no trouble at all setting it up. This program also saves the weather data in an archive file so you can access it as needed. I used to have a weather station made by MFJ Enterprises a few years ago and it had a nasty software program called Heavy Weather. It took me forever to figure that program out!
In summary, let me say that I am very pleased with this new weather station. I think I got a good value for my money. LaCrosse will not see another dime from me, tho.
Here is an update on the Meade weather station. When I updated my computer to Windows 7, I found that the Meade software would not work. I went on-line to the Meade website and found that they don't provide updates to their software packages! I tried looking elsewhere on-line for software that might work but I had no luck. By this time, the weather station was showing its age and battery life was getting shorter, so I decided to go shopping for yet another weather station.
I ended up with a nice one from Acurite, which cost $225. The outside unit was an all-in-one outfit and it sends data wirelesssly to a receiving unit inside the house and that unit is connected to my router, which sends the data to a website from which I can access my data from any Wi-Fi hotspot or standard internet connection. THAT is COOL! The display unit is a full-color LCD outfit with back-lighting. I usually have to change batteries in the sending unit about every 4 months. I did not put the sending unit up very high this time. It is about 12 ft. off the ground on a self-supporting mast and works fine there.
Wednesday, November 13, 2013
Keeping Track Of Your E-QSLs
This may be helpful to hams who use the eQSL.cc website. I have come up with an easy way to keep track of my eQSL cards that I have downloaded. I created a folder in My Documents called E-QSLS. Within that folder, I created subfolders for each digital mode plus SSB. Then within those folders, I created subfolders for contests, special events and DXpeditions. See the flow chart below.
FLOW CHART
E-QSLS
|
PSK31-Contests
Special Events
DXPeditions
|
RTTY-Contests
Special Events
| DXpeditions
FELD HELL-Contests
|
Olivia
|
MFSK
|
SSB-Contests
Mobile Contacts
6 Meter Contacts
Special Events
When I save an e-QSL, I save them as JPEG files using the operator’s callsign and the date of the QSO for the filename: W9XYZ 11-13-13 for example. If I happen to work this guy again, I will save it with the date of the next QSO: W9XYZ 12-15-13 for example. If you work someone operating portable such as W9XYZ/4, don’t save it as W9XYZ/4 because the computer will be confused by the slant bar. Instead, save it as W9XYZ-4. When you download e-QSLs, you can choose which file type to save it as. JPEG works the best because it is recognized by many photo processing programs. Picasa works great for storing e-QSLs, too. It is easy to print them out when needed. When at the eQSL.cc website, click on My Profile, then go down to Advanced Features where it says “eQSL Display Format”. There you can choose either JPEG or PNG format.
Speaking of printing e-QSLs, you should remember to print them with a border on them because when you print borderless, the left hand edge gets cropped. Having the border prevents this from happening. It may not show up that way on your computer, but it will when it prints. I usually don’t print stateside eQSLs, but I do print the DX ones. If you don’t want to print them out using your own printer, there is a cheaper alternative….Wal-Mart. Put your e-QSLs on a CD and print them out at the Wal-Mart Photo Center. You can use one of the computer kiosks and have it print in bordered form. I haven’t done this in a while, but it is much cheaper than doing it yourself at home.
As with anything on computers, make sure you have a backup copy on an external hard drive or store it on “the cloud” such as Google Drive or something like that. I make a backup copy of My Documents on a backup hard drive, which includes my eQSL files.
If you find this helpful or if you have other ideas, I would appreciate your input. Post a comment if you like.
73,
John Gercken, AA9UF
Monday, January 2, 2012
Choosing the right kind of coax connector.
There are some things to keep in mind when buying PL-259 or SO-239 coax connectors. If the material holding the center pin is white or clear, DON'T BUY IT! I have found that these materials will not tolerate much heat from soldering. They will melt and come out of the barrel. The best type are connectors that are either brown or baby-poo yellow. These stand up to heat very well and can even be reused. I try to buy Amphenol brand coax connectors if possible. I think they are the best. Beware of buying coax connectors at hamfests. I have seen some that are factory rejects and some of the center pins are undersized. This causes problems in getting the center conductor of the RG-8 coax to fit.
If I ever need to cut off a coax connector from a cable, I try to leave at least an inch of coax sticking out the back side of it so I can grab it with a pliers while heating up the center pin and outside of the barrel with a propane torch. I have a small torch head that is on the end of a rubber hose and it has a sleeve that you turn to turn on the gas. The other end has a cap that fastens to the propane cylinder. It was rather expensive to buy, but very handy. You can regulate the amount of heat more precisely than with a standard torch head.
Once I get the old piece of coax out, I set it aside to cool for a while. When it is safe to touch, I take a Swedish file and file the area around the 4 holes in the barrel so it is shiny brass. This also gets rid of burned soldering flux. I also use the same file to clean the inside of the barrel of solder fragments and any wire whiskers that may be still sticking to the inside. Once this is all done, the connector is reusable.
If I ever need to cut off a coax connector from a cable, I try to leave at least an inch of coax sticking out the back side of it so I can grab it with a pliers while heating up the center pin and outside of the barrel with a propane torch. I have a small torch head that is on the end of a rubber hose and it has a sleeve that you turn to turn on the gas. The other end has a cap that fastens to the propane cylinder. It was rather expensive to buy, but very handy. You can regulate the amount of heat more precisely than with a standard torch head.
Once I get the old piece of coax out, I set it aside to cool for a while. When it is safe to touch, I take a Swedish file and file the area around the 4 holes in the barrel so it is shiny brass. This also gets rid of burned soldering flux. I also use the same file to clean the inside of the barrel of solder fragments and any wire whiskers that may be still sticking to the inside. Once this is all done, the connector is reusable.
Sunday, January 1, 2012
Soldering Coax Connectors for RG8X.
Here is an almost fool-proof way of soldering a coax connector for RG8X coax. First, strip off 1 1/8" of insulation from the coax as in this picture.

Now, separate the strands of braid into 2 groups and twist them together as shown.

Now, slide the RG8X reducer up to the separated braids, then clip the braid ends so that they don't hang down past the threads on the reducer.

Now, strip the insulation from the center conductor just above the reducer, then twist the strands together. Take the soldering gun and "tin" the end of the conductor to keep the strands together.

Now, prepare the barrel of the connector for soldering by filing away the plating around the 4 holes in the middle of the barrel. I have found that the plating interferes with good solder flow. You will be filling these holes with solder later.

Next, we slide the barrel over the coax end and screw the reducer on, watching that the center conductor goes thru the center tube. I use a channel-lock pliers to screw the reducer on.

You will see that the two strands of braid are over two of the holes in the barrel and the center conductor sticks out from the end of the center tube. Trim the excess wire off flush with the end of the center conductor tube. Now, it is ready to solder.

Now, we can solder the center conductor to the tip.

Next, we solder the 4 holes in the middle of the barrel. The technique for doing this is to position the connector so the center pin is facing either to your left or right. Then get the iron good and hot. Touch the tip of the iron at the top edge of one of the holes, then feed solder to the tip, dragging it over the hole until the hole fills up with solder. It is important that these holes be soldered shut because I have found that small amounts of RF can leak out, causing RFI in the ham shack.

Now, all that is left is to slide the threaded sleeve up over the coax and screw it onto the barrel. Of course, be sure to check the connector out with a multimeter first to be sure there is no short circuit between the center pin and the barrel of the connector.
Now, separate the strands of braid into 2 groups and twist them together as shown.
Now, slide the RG8X reducer up to the separated braids, then clip the braid ends so that they don't hang down past the threads on the reducer.
Now, strip the insulation from the center conductor just above the reducer, then twist the strands together. Take the soldering gun and "tin" the end of the conductor to keep the strands together.
Now, prepare the barrel of the connector for soldering by filing away the plating around the 4 holes in the middle of the barrel. I have found that the plating interferes with good solder flow. You will be filling these holes with solder later.
Next, we slide the barrel over the coax end and screw the reducer on, watching that the center conductor goes thru the center tube. I use a channel-lock pliers to screw the reducer on.
You will see that the two strands of braid are over two of the holes in the barrel and the center conductor sticks out from the end of the center tube. Trim the excess wire off flush with the end of the center conductor tube. Now, it is ready to solder.
Now, we can solder the center conductor to the tip.
Next, we solder the 4 holes in the middle of the barrel. The technique for doing this is to position the connector so the center pin is facing either to your left or right. Then get the iron good and hot. Touch the tip of the iron at the top edge of one of the holes, then feed solder to the tip, dragging it over the hole until the hole fills up with solder. It is important that these holes be soldered shut because I have found that small amounts of RF can leak out, causing RFI in the ham shack.
Now, all that is left is to slide the threaded sleeve up over the coax and screw it onto the barrel. Of course, be sure to check the connector out with a multimeter first to be sure there is no short circuit between the center pin and the barrel of the connector.
Subscribe to:
Posts (Atom)