Monday, June 27, 2022

 

FIELD DAY 2022 By John E. Gercken, AA9UF I was all excited about this year's Field Day exercise because I thought I was going to have two friends come over to participate. My brother, Glenn, N0PNQ, could not come this year because he had just gotten out of the hospital from surgery. One doctor friend of mine, Dr. James Derk, said he would come over, but he did not bring his radio. His radio was an SDR affair, all operated by computer. He pretty much wanted to check out my station, I think. Well he was blown away by what he saw, but he only stayed about 2 hours. He said he is in the middle of building a deck on his house and wanted to make some headway while the sun was shining. The good news is that he is looking forward to next year's Field Day. I gave him a short tutorial on making contacts. I started out by using FLDIGI software for doing PSK31 and other digital modes but I quickly found that the radio (Icom-7300) would not talk nice with my computer. No matter what com port I used, they just would not play nice in the CAT department. The PTT worked fine. Seeing that I was not going to make any contacts using FLDIGI, I opted to use Airlink Express. It played nice with the radio but I could not get anyone to hear me even with 60 watts being thrown at them. I was getting desperate now. I started MixW and got it configured for Field Day. Everything worked but when I hit the SAVE button after a contact, the information would NOT go into the on-screen log bar. It would go into the full logbook instead. I knew what causes this from previous experience. The dates and times of the contest period need to changed. The start time needs to read 6/25/2022 18:00:00 and the end time needs to read 6/26/2022 20:59:00. I made the changes but the darn thing STILL would not work. I finally decided to "crash" for the night at around 10:30 pm because I was so tired and frustrated. About an hour later, another thunderstorm went through and dumped a bunch more rain on us, about 1.5". Then at about 3:00 am, my wife called me on the intercom saying that our 16 year-old Border Collie, Kate, aka "Poochy Dog" had diarrhea and pooped all over the back hall. Guess who got to clean it up. That took me 45 minutes. Since I was already up, I decided to work some more Field Day stations. I tried 20 and 40 meters but no luck there. I went back to the recliner for another nap. Maybe God will intervene and fix MixW for me. I prayed. I have run out of ideas. After my "clean up" detail, I turned my MixW program back on and much to my surprise and delight, IT WORKED! The callsigns went into the log bar like they were supposed to and stayed that way through the rest of the contest! I give God the credit for this. I checked 20 and 40 meters for activity but there was next to nothing there, so I left the radio on just enough that I could hear it if signals were present. At around 6:00 am, I heard activity, so I quickly moved from the recliner to the ham desk chair and started working stations on 20 meters using PSK31 mode. It got to be so hectic that I could not work them fast enough! Some stations would not let me get finished with one station before they would start calling me! I wasn't complaining....just grinning from ear-to-ear! Of the 84 Field Day sections, I worked 42. I worked a lot of stations east of the Mississippi River but not much was forth coming out of the northwest. Of course, with all my problems I had to deal with, I probably missed out on some good DX. But, with the short time I had left, I ended up with53 contacts. I was hoping to maybe get some RTTY contacts and some on 6 meters but none was to be had. It is strange how things vary from year to year. One mode or another seems to be dominant and one region of the country will have more activity than another. Often, the wee hours of the morning such as 3 to 5 am would be totally dead but once the Sun comes up, it is a totally different story. Stations would come out of the northwest, southwest and the plains. Then the closer to Noon it gets, the signals fade away. Now that the 2022 Field Day event is in the history books, plans for next year are already rolling around in my brain. The first thing I want to do is build an extension on my hitch on the truck or my lawnmower to accommodate the generator. Both of them are about 12" too high. I also want to get a better canopy to put up over the generator. The one I have is a piece of junk and quite old. I would like to find one that can be put up by one man, if there is such a thing. I don't bend very well anymore and my balance leaves a lot to be desired, but I keep trying.

Saturday, January 9, 2021

The Aftermath of the Ice Storm

     The ice storm that hit Central IL this winter (2020-2021) did some pretty major damage in the area.  My east and north yards looked like war zones with limbs down all over the place.  It will take me quite a while to get it all cleaned up because I don't move as fast as I used to and I have a bad back and poor balance.  Below are some photos I took.  There is a big tree out behind the barn that really got hit.  The top of it looks like a whirlwind got it.  We were very fortunate in that neither of my Ham Radio antennas were damaged and there was no damage to the house or vehicles.











     I hauled 3 pickup truck loads to the burn pile today (1-9-21) and it barely made a dent in the mess.

John, AA9UF

Tuesday, March 10, 2020

Live long and prosper. \\//

In light of the fear over the Corona Virus, it might be a good idea for us to change the way we greet each other.  I think we should temporarily adopt the Vulcan hand sign \\// like Mr. Spock did on Star Trek.  When he gave the hand sign, he said "Live long and prosper."  If he was greeting another Vulcan, the other man would hold up the same sign and say in response, "Peace and long life."  It would be infinitely more healthy and a bit more meaningful.  Your comments are welcome.

\\// Live long and prosper.

John, AA9UF

How to install a PL-259 coax connector on LMR-400 coax.


     Every ham radio operator has little tricks to help him do things such as installing a PL-259 coax connector on a piece of coax cable.  I would like to share my method.
     First, I strip off about 1" of insulation from the end of the coax cable with a utility knife (aka box cutter).  Then I take a cable stripper and position it right in the middle of the exposed coax braid.  Put your finger in the loop and make 4 or 5 turns around the coax.  You should end up with about 3/8" of coax braid on the coax.  

     Now, get a small file and file off the nickel plating from around the 4 holes in the barrel of the connector.  I have found that solder does not like to stick to nickel very well.  

     Before you begin this next step, make absolutely sure there are no small wires sticking up near the center conductor of the coax.  If even one of those little whiskers gets in the wrong place, it can cause a short in the coax if it makes contact with the center conductor.   
      I have a very handy little tool that a good ham friend of mine made which consists of a PVC Tee and an SO-239 coax connector  glued into the middle hole.  Thread the coax connector on to the T with the connector's bezel.  Now carefully stick the end of the coax into the back of the connector.  Grab the T firmly with one hand and the coax in the other and twist the T toward you about 11 times until you feel resistance.  

     Now take the Tee off the connector and check to see that you can see the braid through the 4 holes in the barrel and check the center pin to see that the center conductor is poking through. 

     Now we are going to dab some soldering paste on the 4 holes in the connector barrel.  You can use any little stick such as a Q-Tip with the cotton cut off the tip to dab it on.  This step insures that the solder will flow down into the holes, creating a good seal.  This step is important because if those holes are not sealed, RF can leak out and cause interference to other components of your ham station.

     Next, we solder the center conductor to the center pin of the connector with my Weller 200 watt soldering gun.  I strongly suggest putting the coax in a vise but don't tighten it down too tight.  You don't want to damage the cable in any way.   The vise will keep the coax from turning while you solder.  

     Now, we solder the 4 holes in the barrel.  Position the coax connector so that the center pin is pointing to your left.  Now, position one of the 4 holes so that it is looking directly at you.  Make sure your soldering iron is up to operating temperature, then apply solder to the tip while holding the iron on the area just above the hole.  Now slowly drag the iron down over the hole and pull it away.  If the iron does not completely cover the hole, do it again.  If you are successful, repeat for the other 3 holes.  Let the coax connector cool off before removing it from the vise. 

     Next, we check continuity with a multimeter set to the OHMS setting so that when you hook the two leads together, the meter emits a beep.  Connect the black lead to the center pin and the red lead to the barrel of the connector.  If  NO beep sounds, then there are no shorts in the connection.  If there IS a beep, you will not be able to use that piece of coax.  You will have to cut the connector off and install a new one.   The last thing you need to do is scrape the brown rosin off the center pin of the coax connector with a knife then shine it up with some Scotch-brite.



   


Tuesday, January 14, 2020

Model of the starship USS Enterprise


This  AMT model of the Enterprise was a real booger to put together.  There were very few pins and pockets for parts alignment and the modeling glue took forever to set up.  I ended up using Gorilla Super Glue instead.  In some areas I had to use a hot glue gun.  The forward end caps of the warp nacelles were too thick to let any of the red LED light thru so I used two caps from 1 liter soda bottles instead.  Also, I had to drill a hole thru the middle of the two clear plastic domes because the LEDs I installed were just a bit too tall and I had nothing else to use.
     The decals for this model are NOT the kind where you dip the paper in water to loosen them up.  You simply peel them off the dry paper and they stick on.  The instructions say that you need to dip them in water, but that is wrong.
     It took me 2 weeks to put this thing together which is way longer than I expected due mostly to all the wiring of the LEDs that I did.  I powered it with a 5 VDC wall wart from an old cell phone.

Friday, April 26, 2019

Lament Of A Ragchewer


     My, my!  How things have changed in the digital world of Ham Radio.  It used to be that the 14.070 frequency was crowded with hams having  meaningful conversations with other hams around the world.  Now, you are lucky to see 2 or 3 traces.
     Everybody has left town and gone to the gold fields of FT-8 and JS8Call where they just exchange callsigns and 599s then move on to the next contact.  That saddens me because they are missing out on the real meaning of communication.  What is communication?  It is the exchange of thoughts and ideas between humans.  In having an exchange of thoughts and ideas, we usually tend to learn something from it.  I don't see that happening with FT-8 or JS8Call.  I have done both and neither one appeals to me at all.  JS8Call sends out 13 words at a time and takes 15 seconds to send a string.  You can take a power nap in that time.  It is my hope that  perhaps FT8 and JS8Call will eventually die out and more hams will come to realize what they have been missing.
     We are supposed to be trained communicators according to Part 97 of the rules.  Are we doing that?  My answer, for the most part, is "no"...at least not in the digital world from my experience.
      Whenever someone tries to get by with a "hit and run" contact with me, I do my best to not let them get away with it.  I ask them why they want to quit so soon.  If they tell me that their English is not so good, I tell them that they won't get better at it if they don't practice using it.  Usually, they do engage in conversation and in by the time we are done, they tell me how much they enjoyed it. Then I say to myself , "Well another one bites the dust."
     Pretty soon, we are going to forget how to communicate effectively.  Just take a look at some of the phone texting that goes on.  It is replete with poor spelling and grammar.  Almost nothing is spelled out.  It is all abbreviated or somehow butchered in one way or another.
     Try listening to a TV news program.  My wife cringes every time she hears the local TV news....poor grammar everywhere!  Don't they have anyone who proof reads the script?  My wife taught 6th grade for 35 years, so she knows her stuff about spelling and grammar.

Wednesday, March 6, 2019

Setting Up The SignaLink USB Interface For Digital Ham Radio

     I have noticed quite a few hams on the air having trouble configuring their radios and interfaces to get a good looking signal out.  I am hoping these tips will help.  I have been doing digital ham radio since the 1980s when the Commodore computers were popular.  I was doing Pactor and RTTY quite a bit.  Then in Sept. 1999 I got into PSK31 and other digital modes as they were developed.
     My digital program of choice is MixW 3.2.105 but most programs are pretty much set up the same way.  They all have a drop-down menu called Configure where you can set up the program and the SignaLink USB.
     Make sure that you have your digital program up and running and your SignaLink is plugged in and turned on.  Turn on the rig, too, because you will need to set up the CAT (Computer Aided Tuning) parameters.
     Go up to the top edge of the program screen and find the word Configure and click on it.  A drop-down menu will appear.  Now find TRANSCEIVER CAT/PTT and click on it.  At the top you will see 2 windows labeled CAT and MODEL.  Click on the little black arrow to the right of CAT and choose which radio you have and click on it.  Now go down to the MODEL window and click on that little black arrow and choose what model number of rig you have.
     Now go further down where it says PTT & CAT Interface and click on the label called DETAILS.  You will see 7 windows labeled Port, Baud Rate, Data Bits, Parity, Stop Bits, RTS and DTR.  Click on Port and you will see port numbers listed there and some will have an asterisk (*) by them.  These are the ones that have COM ports assigned to them.  Choose one.  Now, the numbers that go into the rest of the 7 windows should be as follows: Baud Rate: 9600, Data Bits: 8, Parity: None, Stop Bits: 1, RTS: Always On, DTR: Always Off.  These parameters are for an Icom radio.  If you have a different brand of rig, you might have to check the manual or you could go to the Tigertronics website to see what the parameters for your rig are. Yaesu rigs use a baud rate of 4800.  Once you have those 7 windows filled in, click OK.  There are other things in the menu box that need to be checked: Save frequency on exit can be checked in the little box beside it and CW out via Soundcard can be checked.  Also, AFSK in place of FSK can be checked.  Default digital mode should be USB.  You are now done with this part.  Click OK.  If you do not get an error message saying that the CAT interface Com port is in use or not functioning, this means that it is the correct Com port for your radio.  If you get an error message, you might have to go back to Configure and choose a different Com port number.
     Now go back to Configure and this time we will set up the PTT, sometimes called Secondary PTT Port.  Click on it then click on Port Settings.  You will see a little box with 5 windows in it.  They are labeled: Port, Baud Rate, Data Bits, Parity, Stop Bits, RTS and DTR.  The port number you choose should NOT be the one you chose for CAT.  Baud rate should be 9600, Data bits 8, Parity None, Stop Bits 1.  RTS should be PTT and DTR should be Always Off.  The boxes beside Echo, Disable and Hardware Flow Control should NOT be checked.  Now click OK.
     Now we go back to Configure again and click on Sound Device Settings.  At the top of this box, you will see Device, Input and Output.  Click on the little black arrow and you should see Sound Card (Internal or External, Rig Expert S/D, and Eye Of The Needle.  Click on Sound Card.  Then on the next two windows, click on the little black arrow.  In the Input window, choose Microphone (USB Audio Codec).  In the Output window, choose Speakers (USB Audio Codec).  Next, there is a window called Sample rate.  Type in 12000.  The default is 11025 but having a higher sample rate keeps your TX  signal from drifting. You don't have to do anything with Clock Adjustment or Sound History.  The next 3 windows down are Spectrum Speed, DSP filter and FFT Window.  Spectrum Speed adjusts how fast the waterfall display travels downward.  I like mine at X3.  DSP filter should be: None.  FFT Window should be: Hamming.  I have my DSP filter turned off because I have an outboard MFJ-784B tunable DSP filter hooked up to my rig.  Audio Processing window should be "Message-based (standard).  Now click OK and see if you have a waterfall display.  Tune your rig to 14.070 Mhz and see if you find some signals.  They should be traces that are about 1/4" wide.  Click on one with your mouse and see if the signal is being decoded by the software.
     The volume on the rig should be at about 9:00 and the volume (RX) on the SignaLink should be at about 8:00.  I have my volume set so I just see some slight speckling in the waterfall from the noise floor.
     Here is how I have my waterfall display set up for color display:  Click on View, then find Spectrum and click on it.  Now find Colors then find Waterfall Pallet.  You will see a bar with little squares of color.  You can change these colors by left clicking on each bar and choosing the color you like.  Here is how I have mine configured: black, black black, blue blue, yellow yellow yellow yellow.  This configuration gives me yellow traces on a blue background.  Click Apply then  click Save.  This will let you save your colors to a folder.  I use a file name called 3blk2blu4yellow.pal .  This tells me what the colors are.  I keep a folder called Waterfall Colors within the MixW folder where I keep my waterfall pallet files.
     Here is how you need to set up the rig for best signal output.  First, set the RF power to 100 watts.  My Icom rig uses a port in the back to connect to the SignaLink, so I don't need to mess with the Mic Gain.  TX output is set by the TX control on the front of the SignaLink.  When you transmit with the software, watch your ALC reading!  It should be at ZERO, showing NO reading at all.  If it does, your TX level is too high.  This is the most common mistake that hams make.  You don't need to drive the TX audio nearly as hard with digital as opposed to SSB voice.



Thursday, January 31, 2019

Coax Jumper Tester



     This is a Coax Jumper Tester for testing those short lengths of coax cable that we ham radio operators use to connect our equipment such as connecting the radio to the tuner, the radio to a coax switch, the radio to an oscilloscope, etc.  Testing with a multi-meter can be difficult because the alligator clips on the test leads tend to fall off very easily and they don't provide a solid connection.  This tester eliminates that problem and gives you a more complete test.
     Operating this unit is quite simple.  Take the coax jumper that you want to test and screw the coax connectors to each of the two connectors on the front of the box.  Connect the red/black zip cord to a 12 VDC power source.  First, flip the power switch on, then flip the test switch to the UP position.  This tests the center conductor for continuity.  While this part of the coax is under test, wiggle the coax to see if the indicator light blinks or flickers.  If it does, then you have a bad solder connection.  If the light remains solidly on, then your solder connection is good.  Now flip the test switch to the DOWN position.  Again, wiggle the coax around and see if the indicator light flickers or blinks.  If the light flickers or blinks, the solder connection is bad.  You will have to repair the bad solder connection on the jumper then test it again.
     Here is the list of components:

2    SO-239 chassis-mount coax connectors
1    DPDT toggle switch
1    SPST toggle switch
2    12 VDC incandescent pilot lamps (You can use LEDs if you like.)
1     Fuse holder
1     3-amp glass tube fuse
1     6 x 4 x 2" plastic project box
3 ft.  #18 red/black zip cord (You can make the cord as long as you need.)
5     6-32 x 1/2" Philips head screws
5     6-32 nuts
Various lengths of #18 hook-up wire
4     red fork terminals


     This blogger does not accept PDF files, so I had to take a photo of the schematic in order to get it posted. 
     Your comments and suggestions are welcome.

73,

John Gercken, AA9UF

Friday, January 18, 2019

Getting Back To CW After 8 Years.

     For many years I had doggedly kept trying to improve my skills as a CW (Morse Code) operator in Ham Radio.  It seemed that the more I practiced the worse I got at copying.  Sending was not an issue, but my copy of anything beyond 12 wpm was beyond what my feeble brain could do.
     I did manage to pass my 20 wpm code test to qualify for my Extra Class ham radio license, but it took 3 tries to get there.  I finally passed on the 3rd try.  After jumping that hurdle, I never tried keeping up the 20 wpm speed because I was just not comfortable copying at that speed.  My brain was just not wired for it.  I tried some QSOs at speeds approaching 20 wpm but I felt exhausted once I got done.  I thought to myself..."Is why we say we "work" a station?  This is not my idea of fun!"
     So, I went back to my old comfortable speed of 12 wpm.  Much to my chagrin, I kept running into high-speed operators coming back to me at the speed of light, expecting me to copy.  I refused to even try and either signed off or went to another  part of the band.  Sometimes I would say "NO QRS, NO QSO." but they still came back at their speed of light, ignoring my request.  At one point I even joined a CW club called FISTS who claimed that they would slow down for slower operators.  I quickly found out that they fell into the same bad habit of creeping up to the speed of light just like all the other hot-shot operators.
     In frustration, I finally sold all 3 of my CW keys and automatic keyers and concentrated my efforts in the digital modes such as PSK31, RTTY, Feld Hell and whatever others I could find on the air.  I was a much happier camper.
     But now, things have changed again.  My oldest granddaughter, Julianna, age 9, is studying for her Technician License and seems to have a keen interest in CW.  Well, like a good grandpa, I bought her the MFJ Morse Tutor so she could practice.  Since I had been CW-free for 8 years, I knew that my CW skills were pretty rusty by this time.  So, I bought a Vibroplex iambic key and started listening to CW signals on the air and I did some keying with the rig power turned way down and the tuner on the dummy load setting to get my fist and brain used to the idea of CW again.
     I decided that the best thing to do would be to stay the hell out of the Extra Class portion of the CW band on 40 meters.  That way the chances of me running into a speed-of-light operator would be minimized.  So far, after 4 QSOs, I have been pleasantly surprised and pleased at my progress and I actually ENJOYED it! GASP!  I have no intention to attempt 20 wpm, tho.  I will stay right where I am comfortable.

Wednesday, January 2, 2019

A Better Way To Anchor The MFJ-2990 Vertical Antenna.

     I have 2 of the MFJ-2990 Vertical HF antennas and here is my method of anchoring them.  First, I use the MFJ-1903 Tilt-Over base.  This allows me to raise and lower the antenna without any help.  Don't try to raise it by trying to balance it vertically unless you have a second man to help position it on your mast.  Using the Tilt-Over base is the way to go.
     Here are my suggestions on guy ropes.  Use 3/16" black dacron rope.  Tie one end of it at an anchor point about 2/3 of the way up the antenna.  Tie the other end to a clothes line rope tensioner

     Next, I inserted a carabiner into the end of the screen door spring and attached the carabiner to the rope tensioner.  At the bottom of the screen door spring I looped a 4 ft. length of 1/8" wire rope through it and fastened it with small u-bolts specifically made for wire rope.  At the other end of the wire rope, I looped it through the ring on the anchor stake and secured it with u-bolts.
     Why do I use the 4 ft. of wire rope?  I have had rabbits, birds and even mice chew through the dacron rope if it is tied at the ground stake.  The critters can't chew through stainless steel. I have seen Robins peck at the dacron rope thinking it is a worm.
     This is the anchor that I use on the antenna.  It is available from DX Engineering.

    This is a close-up of the tensioner and spring assembly.  This setup works well because the spring keeps tension on the rope and also lets the vertical sway in the wind to some degree.  In the past, I had problems with guy ropes breaking when the wind got too strong because the antenna would jerk on the guy rope.  The spring prevents that from happening.
     One little tip...an easy way to thread the dacron rope through the tensioner is to take a piece of #12 copper wire about 8" long and make a 1/4" diameter loop in one end, just enough to get the dacron rope through.  Don't tie the dacron rope to the copper wire because the knot will not go through the tensioner. Poke the end without the loop down through the top end of the tensioner while keeping a hold of the end of the dacron rope to keep it from slipping through the loop on the copper wire.  You might need a vice-grip to grab onto the copper wire and pull it through.
     Adjusting the tension on the rope is easy.  To make it tighter, just pull the rope through the tensioner.  To loosen it, pull on the insert inside the steel loop of the tensioner to release the tensioner's grip on the rope.  The rope is held in place by 3 ball bearings in the top of it.
     The only downside of the tensioner is that the ball bearings are not stainless steel and tend to rust.  I don't know how hard those bearings are to remove, but I would like to find some stainless steel bearings to replace them with.

73,

John, AA9UF

Thursday, December 13, 2018

The SignaLink USB and snap chokes

     I learned something today.  I had been having trouble with vertical lines on my waterfall display on my digital program MixW, which I thought were caused from computer noise.  I put 2 rather hefty snap chokes on the Radio line and the USB line going into the SignaLink.  This caused another problem.  Whenever I would transmit, the Delay function would click my signal out, causing gaps in my tansmitted text.  I found that I had to remove those snap chokes and the delay clicking went away.  Also, on closer examination, I found that one of my cables for the computer speakers was in the wrong port.  The vertical lines went away.

Monday, September 3, 2018

Tips on Mobile Ham Radio Installations

     I often get asked about mobile ham radio installations, so I thought I would post some tips on that subject.
     First and foremost, good grounding is of prime importance, especially doors and hoods.  In every vehicle I have owned, I took a piece of 1/2" ground braid and put crimped ring-tongue solderless terminals on each end then fastened it between every door and the frame.  I did the same to the hood and frame.  Remember to do the same to the car's trunk, too.  This practice ensures that each component of the vehicle has the same ground potential.  Even tho the doors and hoods are connected by hinges, you have to remember that those hinges have grease on them and grease is an insulator when it comes to electrical current and ground paths.
     The exhaust pipe can act like a giant antenna, too, causing QRM.  It is not connected to the frame of the vehicle solidly because it needs to "float" by means of some special brackets that have a piece of thick rubber in between.  So, I take a piece of ground braid and connect it between one of the muffler clamps and a bolt on the frame.  If there is no bolt nearby, find a thru hole in the frame and stick a bolt thru it.  Or, you could drill and tap a 1/4-20 hole in the frame and fasten the braid to that bolt.  Make sure you use a lockwasher on that bolt to keep it from vibrating loose.  If there is any undercoating on the frame, scrape a little of it off before inserting the bolt, then once it is tight, spray some touch-up undercoating on the bolt.
     The DC power line should be ran directly from the battery thru the firewall to a screw terminal strip inside the vehicle.  Make sure the terminal strip has enough terminals to acomodate all of the stuff you will be hooking to it.  I use #10 stranded wire for the battery run and it is the red/black DC wire that is standard for automotive work.  At the battery end, solder in an in-line fuse holder and fuse it with a 25 amp fuse.  Also, at that same end, put a big snap choke there with as many turns of wire as you can get on it.  Put another snap choke on the other end of the DC cable.  This will help attenuate alternator whine and fuel pump noise.  Snap chokes can be purchased from www.allelectronics.com fairly cheap.
     Lets talk a bit about antenna installations.  With dual band 2M/70cm antennas, I always try to use a mag mount and I put it right in the middle of the roof.  This gives the antenna a good ground plane for the signal to reflect off of.  The signal will be strongest in whatever direction the vehicle is facing, front or back.  If you have a regular car, you can use a trunk lip mount for the antenna and that will work OK, too.  Routing the coax from a roof mounted antenna, I just run the coax to a rear door and shut the door on the coax somewhere near the top.  I don't usually have any problems with water leaking in when it rains.  Routing the coax from a trunk lip mount can be tricky because you have to snake it under the back seat and up front to the radio.
     What is the next thing you need to do now that you have the radio and antenna installed?  Check the SWR! For this you will need a good quality SWR/Power meter.  You will need to set the radio on a simplex frequency such as 146.520 and check the SWR there.  A reading of 1.3 or lower is acceptable.  Now set the radio to the 70cm band and put the frequency at 449.00.  Why 449?  Because most 440 repeaters have a 5 khz split between the receive and transmit frequencies.  In other words, if you are on a repeater that is on 444.100, your rig will transmit on 449.100.  This is where you need to check your SWR.  Most dual band antennas don't have SWR readings that are equal on both bands.  Sometimes you have to play with the adjustable whip on the antenna to strike a happy medium.  I try to get them as close as possible to each other.  There have  been times when I have had to trim a bit of material off the bottom of the whip with a bench grinder, but you have to be VERY CAREFUL about this.  If you trim even a few thousandths of an inch too much, it can change the SWR dramatically.  Don't do this unless there is no alternative.  Another option is to raise or lower the position of the whip in its socket then tighten down the setscrew.
     Now lets talk a little bit about HF antennas.  I have used Ham Stick antennas and Hustler antennas but the drawback of those is that in order to change bands, you have to change antennas, which can be a big pain in the butt.  I thank God for the invention of the screwdriver antenna!  The one I use on my truck is the Little Tarheel II which will transmit on 80 thru 6 meters.  Again, the key to getting an antenna to work well is a GOOD GROUND.  On my truck, I took a piece of 1/8" aluminum and bolted it between the tool box and the truck bed with about half the material sticking out beyond the truck bed.  The antenna is mounted thru a hole in the material.  I then ran a piece of copper wire from that plate to the frame of the truck for the ground connection.  This arrangement works well.  It is out of the way and yet high enough for the antenna to use the roof as a ground plane.  I use an Ameritron screwdriver antenna controller for tuning but it can  be a pain in the butt because if the antenna loses its position, the preset position numbers on the controller will be off, too.  That is why I have ordered an autotuner for the antenna.  I have not installed it yet and I do not remember the name of it, but as soon as I get it installed and working, I will add a product review to this blog.
     The radio I use in the truck is the Yaesu FT-857D because it has HF, VHF and UHF all in one box.  Believe me, I use all of its capabilities, too.  I have had it since 2007 and it has been a very good performer.  When I am on HF, a lot of guys can't believe I am mobile because they don't hear any noise from the truck!  I guess the noise cancelling ability of the stock mic works quite well.  There are times when I wish I had an amplifier in the truck for HF, but then I would need a heavier duty screwdriver antenna to handle the extra power....maybe someday.

Wednesday, February 24, 2016

Frequently Asked Questions About Ham Radio


Why are you called “hams”?
     Nobody knows for sure, but my own theory is that when ham radio first began, our radios had to be built from scratch, and the only mode of operation was AM.  I think the word HAM meant “Homemade AM.”
     However, HAM can mean Help All Mankind, because when disaster strikes, we hams are some of the first on the scene.  Remember the Great Flood of 1993 along the Mississippi River?  Ham radio operators spent countless hours relaying messages, hunting for survivors, handling logistics, and many other things on their own time and at their own expense.
     Here in Illinois and throughout the Midwest, we most often do weather spotting.  When severe weather threatens, trained spotters are sent out into the countryside around the cities and towns to watch for tornado activity in the sky and report back via VHF or UHF radio to their “net control station” which is usually located at the Emergency Operations Center at ESDA headquarters or a firehouse.  The net control operator also watches the Doppler radar display on the Internet and warns his spotters of imminent danger in their location.
     Helping others in any way we can, is our “prime directive”.  When disasters occur, often times the phone lines are down and electrical power is knocked out.  All normal means of communication are useless...even cell phones.  Our job is to be constantly on the cutting edge of technology and to be ready to set up our stations at a disaster site at a moment’s notice.  Field Day is our once per year opportunity to test our equipment and expertise at communicating under difficult conditions outside our homes.  Many ham radio clubs work closely with local governmental and disaster agencies throughout the year in planning for disaster management.
How far can you talk?
     That depends on the type of radios we use, and what modes of operation we use.  If we were to use VHF or UHF radios, they would have a range of about 15 miles if we did not go through a repeater system.  If we use a repeater, our range would be extended to about a 35-mile radius of the repeater’s location.  A repeater is basically a remote radio site, which takes our transmitted signal and rebroadcasts it simultaneously at a higher power level.  Repeaters are usually located on the tops of tall buildings, or commercial radio towers.  There are many thousands of repeaters on many different bands all across the U.S. and the world, which are owned and operated by ham radio clubs and individuals.
     If we were to use a radio, which operates below 30 MHz, we can talk all around the world if propagation conditions are good.  We call these bands the High Frequency bands, or HF for short.  Back in the early days of ham radio, many thought that the highest they could possibly go in radio frequencies was 30 MHz because the technology to do otherwise did not exist at the time.  Now, however, things are different.  Some ham operators have been experimenting with frequencies in the 24 GHz  (Gigahertz) range, which is at the high end of the microwave band.
     Since the Space Shuttle missions began, ham radio has been onboard, and we have been able to talk to the astronauts directly.  Many hams have set up stations at schools around the country and let the school children ask the astronauts questions.  The first astronaut to use ham radio aboard a shuttle was Owen Garriott, W5LFL.
     Some hams with a lot of real estate for large antennas have been able to bounce VHF radio signals off the Moon and back to Earth.  We call this mode EME, which stands for Earth-Moon-Earth.  The signals that come back from the moon are quite weak, so a large antenna array is needed to pick them up.  Receiver preamplifiers are also needed to boost the incoming signals.  Most EME transmissions are done in Morse Code.  A lot of transmit power is also needed for signals to reach the moon.  Many operators use up to the legal limit of 1500 watts.

What is the difference between CB and Ham Radio?

       There is a HUGE difference.  CB radios are cheaply made and poorly designed.  They only put out 4 to 5 watts on AM and 12 watts on SSB.  On a good day you might be able to talk reliably out to 15 miles or so.  CB radios are limited to only 40 frequencies or channels, which is a very tiny chunk of radio spectrum.  In ham radio, we use entire BANDS of frequencies.  For example, in the 14 MHz band we are allowed to use all frequencies from 14.000 to 14.350 MHz.  There are no assigned “channels”.  That is only one band out of the 10 that we have in the HF frequency spectrum.  I haven’t even mentioned the VHF or UHF bands.  So, you can see how much more versatility we have in ham radio as opposed to CB.  Furthermore, we are allowed to experiment with our equipment to enhance its performance.  That is why we are officially called Amateur Radio Operators.  CBers are not allowed to do that.  We can even build our own equipment if we want to, but there are rules and practices to be followed in doing so.  That is why we are required to take written exams.
     CB is not a regulated radio service the way ham radio is.  The only time the FCC steps in on CBers is in cases where repeat offenders cause malicious interference to other radio services or run amplifiers.  Running an amplifier of any kind on CB is strictly forbidden.
     I used to be a CBer back in the early 1970s but I eventually got tired of all the operators interfering with each other, channel bleed-over and profanity on the air.  In 1979 I was introduced to some ham radio operators in the Gibson City, IL area and they started a ham radio class.  On May 20, 1979 I took my ham radio exam and became a Novice operator.  I sold all of my CB stuff and bought my first ham radio.

You guys still use Morse Code?  I thought that was outdated long ago!
     Much to the surprise of many, Morse Code or “CW” is still used today, but to a lesser  extent.  It is still a reliable method of communication, and the simplest to use.  The fact that Morse signals are high-pitched audio tones, gives them the ability to be heard more readily through interference and static.  With electronic filtering devices, we are able to decrease the level of interference and narrow the bandwidth of our radios so that we hear only the signals we wish to receive.  Other CW signals which would be audible and within the bandwidth of the radio’s receiver would be blocked out.  You can’t do that to as great an extent with voice signals without losing a lot of signal quality.  
     Receiving Morse Code is like reading music, only in reverse.  With music, you read the music on the paper, and translate those notes into sound.  With Morse Code, you listen to the sound, then translate that sound to words written on paper.  Some operators are so good at CW (Continuous Wave - another name for Morse Code) that they can copy it in their head at over 40 words per minute, and never have to write anything down!

How do your radio signals go clear around the world?
     Our radio signals are reflected back down to Earth by bouncing off a layer of ionized air about 50 to 250 miles above the Earth.  It is called the ionosphere because it is made up of electrically charged oxygen molecules, called ions.  These molecules are charged by the sun’s “solar wind”.  Within the ionosphere, there are 3 inner layers called the E, F1, and F2 layers.
     The E-layer is made up of patches of ionized air and these float around up there.  That is why we hear signals fade in and out on some of our bands because these patches of air move and change the angle at which our signals are reflected back down to the Earth.  The 50-54 Mhz band, called 6 meters, is affected by the E-layer.  When propagation is favorable on 6 meters, many hams get on the air and make as many quick contacts as possible before the conditions fade.
     The F1 and F2 layers combine at night to form one layer, and this enables our signals to go farther distances.  These layers do not move around, in patches like the E-layer does.  These layers of ionosphere basically act as a mirror in reflecting radio waves.  Many times our radio waves make many “hops” across the earth in this manner, and that is how we can communicate with other hams across the world.
     When the sun is highly active, it produces solar flares.  These huge masses of electromagnetic plasma, x-rays and gama rays produce massive amounts of “solar wind”, and they can disrupt our communications systems.  We hams are especially aware of this, and we are watchful of the U.S. government’s measurements of this activity.  These measurements of geomagnetic activity are broadcast every hour at 18 minutes past the hour on WWV, the station where the Atomic Clock is located.  Visit their website: www.nist.gov for more information.  Also read the July 2004 issue of National Geographic for more information on the latest findings on the sun’s makeup via NASA’s SOHO orbiter.  Another good website to visit is www.solarham.com .

 How many ham operators are there?
     At the last count, there were around 3 million worldwide, and the numbers are growing.  Japan actually has more hams than the U.S. does.  There are  26,206 hams in Illinois and over 800,000 hams in the U.S.

What do you use computers for in this hobby?
     That would be a long list if I told you everything we use computers for.  One of the main things we use them for is generating digital signals and transmitting them through our radios.  A lot of our software for digital communications utilizes the computer sound card to generate and receive digital signals.  The software decodes the signals we hear and displays the text on the computer monitor.  Then when we transmit, the computer sound card generates the necessary signals, which are put through the mike jack on the radio.  The computer also puts the radio into “transmit” mode.  In order to properly do this, we use an interface, which lets the computer control transmit and receive modes.
     Another interesting mode, which utilizes our computers, is called Slow-Scan TV, but it actually has nothing to do with television.  Until the personal computer came along, however, you did need a small TV camera and interfacing equipment to transmit still 

Sunday, December 27, 2015

Improving the MFJ-2990 Vertical antenna.

     I have owned the MFJ-2990 vertical antenna since May of 2009.  It has been a great performer but it has some design flaws.
     First of all, the sections of aluminum tubing are held in place by hose clamps.  These tend to loosen with time and vibration.  Once I had the thing adjusted and tunable on all the bands I work on the radio,  I put a sheet metal screw in each section near the hose clamp to make sure the sections don't slide down and de-tune the antenna.
     An antenna this long (43 ft.) tends to vibrate in the wind especially if it has guy ropes attached to it.  I would not recommend installing it without guy ropes, especially in windy climates like Illinois has.  The vibration tends to loosen clamps and other components.
     The balun box is poorly designed.  The box is held in place at the base of the antenna by two hose clamps which also serve as contact points to the antenna.  This is not a good thing because the clamps tend to get dirt behind them and the aluminum of the antenna tends to corrode there.  To fix this issue, I disconnected the wire that feeds signal to the hose clamps and terminated it to a stainless steel bolt which I installed in the side of the box.  See figure 1.  The cable I used for the outside connection to the antenna is plain old #12 copper wire. The cable you see in this photo is the center conductor of LMR-400 coax. It dry-rotted over time and I had to replace it.  I then connected the other end of the cable to the antenna by means of a 10-32 stainless steel screw tapped into the side of the antenna.
Figure 1.
     The next thing I did was to take out the two blue capacitors and mount them to a circuit board and re-solder them into the box.  One time I could not figure out why the antenna would not tune, so I looked inside the balun box and discovered that one of the wires from the capacitors had broken off! This was puzzling to me, but I figured out that it must have been vibration that caused the connection to weaken.  Putting the capacitors on a circuit board then soldering in some heavier wire for the connection to the coax connector cured the problem.  See figure 2.


     Next, I found that the ground wire connection to the base plate of the antenna was not very good.  I had mistakenly used a zinc terminal on the end of the earth ground wire to connect to the base plate.  These two metals don't like each other.  I took the terminal off and installed a connector made of an alloy that is friendly with copper and aluminum.  I bolted it on with a stainless steel bolt and then polished up the end of the ground wire with sandpaper.  Then, before inserting the end of the copper ground wire, I smeared some Gardner-Bender No-Ox on the end of the wire.  Then I tightened the connector's set screw.  See figure 3.
                                                                       Figure 3.
     Make sure you don't forget to insert the black wire from the bottom of the balun box into the connector as shown.
     These improvements have made a big difference in keeping the antenna in good condition and functioning normally.  Remember that using stainless steel bolts and other hardware are the only way to go when constructing antennas.  They don't corrode or rust and you won't have to replace them unless they break.


73.  Your comments are welcome.





Thursday, June 11, 2015

Weather Stations - You Get What You Pay For...Most of the Time.

     Last August my LaCrosse Technologies Weather Station model WS-2812U-IT went belly-up after just over one year of use.  The anemometer quit on me.  I opened up the anemometer to see if there was any kind of damage, but I only found that the batteries were dead.  I found out the hard way that taking the thing apart is difficult due to one part in particular.  It is a little piece of black plastic in an L shape that covers 5 little LEDs.  If you break this little piece of plastic, you are SCREWED!  A black plastic disk goes in between it and the LEDs to sense the wind speed.  The plastic disk is on the shaft for the wind cups.  I tried to fix my anemometer but failed.  I contacted the company and sent the whole thing back.  They returned it with a new anemometer inside for free.  I set it all back up again and found that the new anemometer DID NOT WORK right out of the box!  I was thoroughly disgusted, to say the least, so I decided "I am done with this company!"
     I went on-line and searched for weather stations of different brands and found one that suits my needs.  It cost me $200 but I found it was well worth it.  It is made by Meade Instruments and it is the model TE923W-M.  This puppy has the usual indoor/outdoor temp and humidity, barometer, wind speed and direction, and rainfall, plus a UV sensor for sunburn risk, moon phase, sunrise/sunset times, and wind chill.  It even has a remote!  You can even have it backlit in blue, but the backlight only stays on for about 30 seconds or so.  The barometer has a bar graph that constantly updates showing you changes in pressure.  It comes with software for making charts and graphs of weather data.  It is called Weather Capture Advance V 1.2.  It is pretty darn cool!  I had no trouble at all setting it up.  This program also saves the weather data in an archive file so you can access it as needed.  I used to have a weather station made by MFJ Enterprises a few years ago and it had a nasty software program called Heavy Weather.  It took me forever to figure that program out!
     In summary, let me say that I am very pleased with this new weather station.  I think I got a good value for my money.  LaCrosse will not see another dime from me, tho.
      Here is an update on the Meade weather station.  When I updated my computer to Windows 7, I found that the Meade software would not work.  I went on-line to the Meade website and found that they don't provide updates to their software packages!  I tried looking elsewhere on-line for software that might work but I had no luck.  By this time, the weather station was showing its age and battery life was getting shorter, so I decided to go shopping for yet another weather station.
     I ended up with a nice one from Acurite, which cost $225.  The outside unit was an all-in-one outfit and it sends data wirelesssly to a receiving unit inside the house and that unit is connected to my router, which sends the data to a website from which I can access my data from any Wi-Fi hotspot or standard internet connection.  THAT is COOL!  The display unit is a full-color LCD outfit with back-lighting. I usually have to change batteries in the sending unit about every 4 months.  I did not put the sending unit up very high this time.  It is about 12 ft. off the ground on a self-supporting mast and works fine there.

Wednesday, November 13, 2013

Keeping Track Of Your E-QSLs


This may be helpful to hams who use the eQSL.cc website. I have come up with an easy way to keep track of my eQSL cards that I have downloaded. I created a folder in My Documents called E-QSLS. Within that folder, I created subfolders for each digital mode plus SSB. Then within those folders, I created subfolders for contests, special events and DXpeditions. See the flow chart below.

FLOW CHART

E-QSLS
|
PSK31-Contests
Special Events
DXPeditions
|
RTTY-Contests
Special Events
| DXpeditions

FELD HELL-Contests
|
Olivia
|
MFSK
|
SSB-Contests
Mobile Contacts
6 Meter Contacts
Special Events

When I save an e-QSL, I save them as JPEG files using the operator’s callsign and the date of the QSO for the filename: W9XYZ 11-13-13 for example. If I happen to work this guy again, I will save it with the date of the next QSO: W9XYZ 12-15-13 for example. If you work someone operating portable such as W9XYZ/4, don’t save it as W9XYZ/4 because the computer will be confused by the slant bar. Instead, save it as W9XYZ-4. When you download e-QSLs, you can choose which file type to save it as. JPEG works the best because it is recognized by many photo processing programs. Picasa works great for storing e-QSLs, too. It is easy to print them out when needed. When at the eQSL.cc website, click on My Profile, then go down to Advanced Features where it says “eQSL Display Format”. There you can choose either JPEG or PNG format.
Speaking of printing e-QSLs, you should remember to print them with a border on them because when you print borderless, the left hand edge gets cropped. Having the border prevents this from happening. It may not show up that way on your computer, but it will when it prints. I usually don’t print stateside eQSLs, but I do print the DX ones. If you don’t want to print them out using your own printer, there is a cheaper alternative….Wal-Mart. Put your e-QSLs on a CD and print them out at the Wal-Mart Photo Center. You can use one of the computer kiosks and have it print in bordered form. I haven’t done this in a while, but it is much cheaper than doing it yourself at home.
As with anything on computers, make sure you have a backup copy on an external hard drive or store it on “the cloud” such as Google Drive or something like that. I make a backup copy of My Documents on a backup hard drive, which includes my eQSL files.
If you find this helpful or if you have other ideas, I would appreciate your input. Post a comment if you like.

73,

John Gercken, AA9UF









Monday, January 2, 2012

Choosing the right kind of coax connector.

There are some things to keep in mind when buying PL-259 or SO-239 coax connectors. If the material holding the center pin is white or clear, DON'T BUY IT! I have found that these materials will not tolerate much heat from soldering. They will  melt and come out of the barrel. The best type are connectors that are either brown or baby-poo yellow. These stand up to heat very well and can even be reused. I try to buy Amphenol brand coax connectors if possible. I think they are the best. Beware of buying coax connectors at hamfests. I have seen some that are factory rejects and some of the center pins are undersized. This causes problems in getting the center conductor of the RG-8 coax to fit.
If I ever need to cut off a coax connector from a cable, I try to leave at least an inch of coax sticking out the back side of it so I can grab it with a pliers while heating up the center pin and outside of the barrel with a propane torch. I have a small torch head that is on the end of a rubber hose and it has a sleeve that you turn to turn on the gas. The other end has a cap that fastens to the propane cylinder. It was rather expensive to buy, but very handy. You can regulate the amount of heat more precisely than with a standard torch head.
Once I get the old piece of coax out, I set it aside to cool for a while. When it is safe to touch, I take a Swedish file and file the area around the 4 holes in the barrel so it is shiny brass. This also gets rid of burned soldering flux. I also use the same file to clean the inside of the barrel of solder fragments and any wire whiskers that may be still sticking to the inside. Once this is all done, the connector is reusable.

Sunday, January 1, 2012

Soldering Coax Connectors for RG8X.

Here is an almost fool-proof way of soldering a coax connector for RG8X coax. First, strip off 1 1/8" of insulation from the coax as in this picture.








Now, separate the strands of braid into 2 groups and twist them together as shown.








Now, slide the RG8X reducer up to the separated braids, then clip the braid ends so that they don't hang down past the threads on the reducer.








Now, strip the insulation from the center conductor just above the reducer, then twist the strands together. Take the soldering gun and "tin" the end of the conductor to keep the strands together.









Now, prepare the barrel of the connector for soldering by filing away the plating around the 4 holes in the middle of the barrel. I have found that the plating interferes with good solder flow. You will be filling these holes with solder later.










Next, we slide the barrel over the coax end and screw the reducer on, watching that the center conductor goes thru the center tube. I use a channel-lock pliers to screw the reducer on.











You will see that the two strands of braid are over two of the holes in the barrel and the center conductor sticks out from the end of the center tube. Trim the excess wire off flush with the end of the center conductor tube. Now, it is ready to solder.











Now, we can solder the center conductor to the tip.











Next, we solder the 4 holes in the middle of the barrel. The technique for doing this is to position the connector so the center pin is facing either to your left or right. Then get the iron good and hot. Touch the tip of the iron at the top edge of one of the holes, then feed solder to the tip, dragging it over the hole until the hole fills up with solder. It is important that these holes be soldered shut because I have found that small amounts of RF can leak out, causing RFI in the ham shack.











Now, all that is left is to slide the threaded sleeve up over the coax and screw it onto the barrel. Of course, be sure to check the connector out with a multimeter first to be sure there is no short circuit between the center pin and the barrel of the connector.